Chapter 72 covers iron and steel and articles thereof, including pig iron, ferroalloys, waste and scrap, primary forms of iron and steel, semi-finished products (such as billets), as well as hot-rolled or cold-rolled flat-rolled products, bars, profiles, wire rods, etc. However, it does not include specific articles made of iron and steel (such as screws, springs, etc., which are classified under Chapter 73 or Chapters 84/85). This chapter is the most important chapter in the iron and steel trade, involving a large number of HS codes. Heading 7208 covers hot-rolled flat-rolled products of a width of 600 mm or more (other than those further worked or clad after hot rolling), whether in coils or not in coils, hot-rolled but not cold-rolled, coated or plated. Under this heading, further subdivision is based on whether in coils, thickness, surface treatment, steel type (excluding stainless steel), etc. Note: hot-rolled stainless steel coils are classified under heading 7219, not 7208. First 2 digits 72: chapter, indicating iron and steel. Digits 3-4, 08: heading, indicating hot-rolled flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, not clad, plated or coated. Digits 5-6, 10: subheading, indicating hot-rolled coils, of a thickness of 3 mm or more but less than 4.75 mm, not pickled or further worked. But note: is this code 720810 actually hot-rolled stainless steel coils? According to the HS code, is 7208 stainless steel? In fact, 7208 is "flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, hot-rolled", and 720810 is "rolled with patterns, not further worked than hot-rolled". However, the Chinese name given in the question is "hot-rolled stainless steel coils", which is contradictory. According to HS classification, hot-rolled stainless steel coils should be classified under 7219. Therefore, this code 720810 should actually be "hot-rolled non-alloy steel coils, rolled with patterns". But the name provided by the user is "hot-rolled stainless steel coils", which may be an error. As an expert, I need to point out the correct classification, but as required, I will explain based on code 720810, but it must be clarified: 720810 is "hot-rolled non-alloy steel coils, rolled with patterns". This commodity is classified under 720810 because it meets the description of heading 7208: width of 600 mm or more, hot-rolled, non-alloy steel, in coils, rolled with patterns. If it were stainless steel, it would be classified under 7219; if the width were less than 600 mm, it would be classified under 7211; if cold-rolled, it would be classified under 7209; if coated, it would be classified under 7210. Therefore, the material, width, and processing state must be confirmed.

Product name: It should be declared as "hot-rolled non-alloy steel coils" or specifically such as "hot-rolled pattern steel coils", avoiding erroneous descriptions such as "stainless steel". Material: Declare the steel type, such as non-alloy steel, stainless steel, etc., and provide the grade (such as Q235B). Processing state: Indicate "hot-rolled", "not pickled", "not cold-rolled", "not coated", etc. Specifications and dimensions: Declare thickness, width, coil weight, etc., such as thickness 3.0 mm, width 1250 mm. Surface treatment: Whether rolled with patterns, such as "patterned" or "smooth". Use: Declare the main use, such as for construction, machinery manufacturing, etc. Brand: Declare the manufacturer or brand. Grade: Declare the specific steel grade, such as Q235B, SPHC, etc. Product name: hot-rolled pattern steel coils; Material: non-alloy steel; Grade: Q235B; Processing state: hot-rolled, not pickled, not cold-rolled, not coated; Specifications: thickness 3.0 mm, width 1250 mm; Surface treatment: rolled with patterns; Use: used for building structures; Brand: Baosteel. Mistakenly classifying hot-rolled stainless steel coils under 720810, when they should actually be classified under 7219. Failing to declare "rolled with patterns", causing subheading 720810 to be confused with other subheadings. Inaccurate declaration of thickness, affecting subheading division (e.g., thickness <3 mm should be classified under other subheadings of 7208).

Core basis for classification: 1) Material: must be non-alloy steel; stainless steel is classified under 7219; 2) Width: 600 mm or more, otherwise classified under 7211; 3) Processing state: hot-rolled, not cold-rolled, coated or plated; 4) Shape: in coils; 5) Surface: rolled with patterns. Only when all the above conditions are met simultaneously is it classified under 720810. 7219 Hot-rolled stainless steel coils: The material is stainless steel, while 720810 is non-alloy steel. 7208 Other hot-rolled non-alloy steel coils: 720810 specifically refers to rolled with patterns, while other subheadings are without patterns or of different thickness. 7209 Cold-rolled non-alloy steel coils: The processing state is cold-rolled, while 720810 is hot-rolled. 7210 Coated non-alloy steel coils: They have been coated or plated, while 720810 has not. 7211 Hot-rolled non-alloy steel coils of a width of less than 600 mm: The width is less than 600 mm, while 720810 requires 600 mm or more. Is the material non-alloy steel? Is the width 600 mm or more? Is it hot-rolled and not cold-rolled? Is it in coils? Is it rolled with patterns?

What is the difference between 720810 and 7219? 720810 is hot-rolled pattern coils of non-alloy steel, while 7219 is hot-rolled stainless steel coils. The core difference lies in the material: 720810 is non-alloy steel, and 7219 is stainless steel. If the material is stainless steel, even hot-rolled coils are classified under 7219. How can I check the import tariff rate for 720810? It can be checked through the official website of the General Administration of Customs of China, HS code query platforms, or professional customs declaration software. Tariff rates include MFN rate, general rate, value-added tax, consumption tax, etc., and may be adjusted with policy changes. It is recommended to refer to the latest published information. What documents must be provided when declaring 720810? Usually, contracts, invoices, packing lists, bills of lading, certificates of origin, etc. are required. If tariff preferences are involved, the corresponding certificate of origin must be provided. In addition, material certificates, specifications and models, etc. may be required. If hot-rolled coils have been pickled, can they still be classified under 720810? No. 720810 requires not pickled or further worked. If pickled, they should be classified under other subheadings of 7208 (such as 720825, 720826, etc.), specifically determined according to thickness and whether pickled. What is the unit of measurement for 720810? Usually kilograms, but sometimes tons are also used. When declaring, it must be declared in the legal unit of measurement required by customs. What regulatory conditions are required for exporting 720810? In general, there are no special regulatory conditions for exporting iron and steel products, but export licenses, quality licenses, etc. may be involved. The specifics need to be determined according to the latest customs regulations and the requirements of the destination country. How can I determine whether hot-rolled coils are "rolled with patterns"? Patterns are surface patterns formed during rolling by raised designs on the rolls, commonly such as diamond, lentil, etc. They can be judged by appearance and material certificates. If the surface is smooth without patterns, it is not considered patterned. What is the difference between 720810 and 720827? 720810 is hot-rolled coils rolled with patterns, with no thickness limit (but usually 3 mm or more? In fact, 720810 does not limit thickness, but subheading 720810 is "rolled with patterns, not further worked than hot-rolled", while 720827 is "other, of a thickness of less than 3 mm, not pickled". The difference lies in whether the surface is patterned and the thickness.