Chapter 72 covers iron and steel and articles thereof, including pig iron, ferroalloys, ferrous waste and scrap, ingots or other primary forms of iron or steel, semi-finished products (such as billets, slabs), as well as hot-rolled or cold-rolled flat-rolled products, bars, profiles, wire, etc. This chapter is the most important chapter on metal materials in international trade, covering a wide range of steel products from raw materials to semi-finished products, but excluding further processed steel articles (such as Chapter 73). Heading 7219 covers flat-rolled products of stainless steel, but plates and sheets of a width of 600 mm or more, whether hot-rolled or cold-rolled. However, according to HS classification rules, 7219 applies only to flat-rolled products, while bars and profiles should be classified under 7221 or 7222. However, the code 721914 provided by the user is actually hot-rolled stainless steel bars, which is contradictory. According to the actual HS code table, 7219 is flat-rolled products of stainless steel, while bars should be classified under 7221 (hot-rolled stainless steel bars). Therefore, the description here should be corrected: Heading 7219 covers flat-rolled products of stainless steel, of a width of 600 mm or more, hot-rolled or cold-rolled. However, to meet the user's requirements, the following content will be explained based on the code 721914 provided by the user, assuming it is hot-rolled stainless steel bars, which may be a clerical error and should actually be 7221. The code 721914 is a 6-digit HS code. The first 2 digits '72' represent Chapter 72: Iron and steel. The 3rd-4th digits '19' represent heading 7219: Flat-rolled products of stainless steel, of a width of 600 mm or more. The 5th-6th digits '14' represent subheading 721914: Other, not further worked than hot-rolled, of a thickness of 4.75 mm or more but not exceeding 10 mm. However, according to the actual HS code table, 721914 corresponds to 'Flat-rolled products of stainless steel, of a width of 600 mm or more, not further worked than hot-rolled, of a thickness of 4.75 mm or more but not exceeding 10 mm'. Therefore, the 'hot-rolled stainless steel bars' provided by the user does not match the code. Bars should be classified under 7221 (hot-rolled stainless steel bars) or 7222 (other stainless steel bars). If the goods are hot-rolled stainless steel bars, they should be classified under 7221, not 721914. 721914 applies to hot-rolled flat-rolled products of stainless steel. Classification should be determined based on the shape of the goods (flat-rolled, bar, profile, wire), width, thickness, processing state, etc. The core difference between bars and flat-rolled products lies in the cross-sectional shape and width: bars are solid long pieces with a non-rectangular cross-section; flat-rolled products have a rectangular cross-section, with width much greater than thickness.

Product name: The specific name of the declared goods, such as 'hot-rolled stainless steel bars', must be consistent with the actual goods. Material: The grade or composition of stainless steel, such as 304, 316, etc., and the content of main alloying elements must be indicated. Shape: Declared as bars, round steel, square steel, etc., and the cross-sectional shape must be specified. Processing state: Such as hot-rolled, cold-rolled, forged, etc., and whether further processing has been carried out must be indicated. Specifications and dimensions: The diameter or cross-sectional dimensions of the bars, as well as the length, in millimeters. Grade: Such as 304, 316L, etc., must comply with international or domestic standards. Use: Briefly explain the use, such as machining, construction, etc. Customs declaration example: Product name: Hot-rolled stainless steel bars Material: Stainless steel 304 Shape: Round bar Processing state: Hot-rolled, not further worked Specifications: Diameter 20mm, length 6000mm Grade: 304 Use: Machining of mechanical parts HS code: 72210000 (Note: The actual code should be 7221, not 721914) Misclassifying bars under the flat-rolled product code 7219, leading to classification errors. Not providing the stainless steel grade, only writing 'stainless steel', affecting classification. Incomplete specification description, lacking diameter or thickness information.

Core basis for classification: According to the General Rules for the Interpretation of the HS, first determine whether the goods belong to Chapter 72. Then determine the heading based on shape (bar, plate, profile, wire), width, thickness, processing state, etc. For stainless steel bars, they should be classified under 7221 (hot-rolled) or 7222 (other). If they are flat-rolled products, those of a width of 600 mm or more are classified under 7219, and those of a width of less than 600 mm under 7220. Therefore, correct classification requires accurate description of the shape and dimensions of the goods. 7219 Flat-rolled products of stainless steel: 7219 applies to flat-rolled products of stainless steel of a width of 600 mm or more, while bars are classified under 7221 or 7222. The difference lies in shape: flat-rolled products have a rectangular cross-section, with width much greater than thickness. 7220 Flat-rolled products of stainless steel, of a width of less than 600 mm: 7220 applies to flat-rolled products of stainless steel of a width of less than 600 mm, and does not apply to bars. Bars have a circular, square, etc. cross-section, not rectangular. 7221 Hot-rolled stainless steel bars: 7221 applies to hot-rolled stainless steel bars, including round steel, square steel, etc. If they are hot-rolled bars, they should be classified under this code, not 7219. 7222 Other stainless steel bars: 7222 applies to other stainless steel bars other than hot-rolled, such as cold-rolled, forged, etc. If the bars have been further processed, they may be classified under this code. Is the product made of stainless steel? Is the shape of the product a bar (solid long piece)? Is the processing state hot-rolled? Has it been further processed (such as cold-drawn, forged)? Are the cross-sectional dimensions and length clear?

What product does HS code 721914 correspond to? HS code 721914 corresponds to flat-rolled products of stainless steel, of a width of 600 mm or more, not further worked than hot-rolled, of a thickness of 4.75 mm or more but not exceeding 10 mm. It does not apply to bars. If you are exporting hot-rolled stainless steel bars, you should check the 7221 series codes. Which HS code should hot-rolled stainless steel bars be classified under? Hot-rolled stainless steel bars should be classified under HS code 7221, and the specific subheading depends on the cross-sectional shape, dimensions, and composition. For example, hot-rolled stainless steel bars with a circular cross-section are usually classified under 72210000. It is recommended to check the latest HS code table based on actual product information. How to distinguish between stainless steel bars and flat-rolled products? Mainly by shape: bars are solid long pieces, with cross-sections usually circular, square, hexagonal, etc.; flat-rolled products have a rectangular cross-section, with width much greater than thickness, and are usually in coils or flat plates. In addition, the length of bars is usually much greater than the cross-sectional dimensions, while the width of flat-rolled products is an important parameter. What elements are required when declaring stainless steel bars? Declaration elements include: product name, material (grade), shape, processing state (hot-rolled/cold-rolled/forged), specifications and dimensions (diameter or cross-sectional dimensions, length), grade, use. Ensure the information is accurate for correct classification. If stainless steel bars are cold-drawn, which code should they be classified under? Cold-drawn stainless steel bars are usually classified under 7222 (other stainless steel bars), because 7221 is limited to hot-rolled. Cold drawing is further processing and may change the classification. The specific subheading depends on dimensions and composition. What is the main difference between HS codes 7219 and 7221? 7219 covers flat-rolled products of stainless steel (width 600 mm or more), while 7221 covers hot-rolled stainless steel bars. The difference lies in the shape of the goods: flat-rolled products have a rectangular cross-section, while bars are solid long pieces. When classifying, the shape must first be determined. How to check the export tariff rate for stainless steel bars? Tariff rates may change. It is recommended to check the latest rates through the official website of the General Administration of Customs or the International Trade Single Window. Usually, the HS code and origin/destination need to be entered. Note that rates under different trade agreements may vary. What are the consequences of misclassification? Misclassification may lead to customs inspection, supplementary taxes, fines, and even affect the company's credit rating. In serious cases, it may be suspected of smuggling. Therefore, it is recommended that companies declare accurately and consult professional customs brokers or customs classification experts when necessary.